Just How to Replace a Bathtub Yourself: Removing and also Replacing.

Schedule An Appointment

What're your insights and beliefs on How to Install a Bathtub?

Setting up a bathtub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the task can move easily; if you have to open up a wall to eliminate the old tub and also position the brand-new tub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have certified on your own for the task and also fit trying it. Rather than hiring a professional to take over a halfway-completed project, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This post will aid you set up a new bathtub in your restroom if you have currently gotten a new tub and do not require to transform the plan of your previous water supply pipes.
Your tools and also material list must comprise the following:

New Bath tub

Hammer

Pipe Wrenches

Prybar

Safety Glasses

Degree

Pliers

Adjustable Wrench

Putty Knife

Screwdriver

Cold Blade

Tape Measure

Pipeline Caps

Preparing for the Installment

First of all, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

Mounting the Bathtub

Using the two wood boards under its feet, position the bath tub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and additionally examine the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub must wait till the tub has been made use of a minimum of once as this will resolve it right into its last placement.

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The previous type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

Tiling Around the Tub

In the area where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a rigid seal, triggering the water to penetrate the wall surface in between the bath and the tiling, bring about problems with wetness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water-proof sticky and also grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I came across that blog post about How to Install a Bathtub Yourself while scouting around the internet. In case you enjoyed our blog entry kindly do not forget to share it. Bless you for your time. Kindly come by our site back soon.

Request Service